0.5 volt dc battery to fool O2 sensor?

[GasSavers_Erik]

I have been driving around watching a digital multimeter which is tied in to my one wire oxygen sensor wire (87 civic with feedback carb.)

The feedback system seems to be doing its job (readings jump around but 90% of the readings are below .45 volts when cruising on the highway). When I floor it, readings jump up to 0.8 and when decelerating in gear, readings go down to near zero volts.

I want to fool the system into leaning the mix out a little, so if I could just feed 0.5 volts into the oxygen sensor wire, then the computer would think it was running rich and tell the carb to lean it out.

Its the same theory behind the "fever buster" mod that is listed here on the intake temp thread.

So, I figure that all I need is a good low amp DC 0.5 volt source that will mimic a rich mixture oxygen sensor signal, but won't have enough amps to fry the computer.

Any ideas from the electronics whizzes here? How about if I use a 1.5 volt battery and a ton of resistors in series, might that be safe?

I am not looking to do this long term, just for a 30 mile test run.

Thanks in advance for any help.

[diamondlarry]

You could do it with three equal sized resistors in series. Tap off of the positive of the battery and at the connection between the first and second resistor of the three and you would have exactly 0.5 volts. Then, connect the circuit in series with the wire going to the O2 sensor with the positive going to the ECU side and the negative to the O2 side. You would want to use fairly high value resistors to limit current flow. If you wanted to have some fine adjustment, you could add a variable resistor in the above circuit.

[GasSavers_Erik]

Originally Posted by diamondlarry

You could do it with three equal sized resistors in series. Tap off of the positive of the battery and at the connection between the first and second resistor of the three and you would have exactly 0.5 volts. Then, connect the circuit in series with the wire going to the O2 sensor with the positive going to the ECU side and the negative to the O2 side. You would want to use fairly high value resistors to limit current flow. If you wanted to have some fine adjustment, you could add a variable resistor in the above circuit.

Thanks diamondlarry! But let me double check that I understand how to do this.

So, I have a simple loop with the positive end of a 1.5 volt battery (example AA) connected to three strong resistors in series and then back to the negative end of the same battery.

Then, I run another wire off the positive end of the 1.5volt battery and connect it to the wire that goes to the ECU and I run a wire from the connection between the first and second resistors and run it to the oxygen sensor. So I am forcing the oxygen sensor output in series through this circuit.

Its the resistor junction that I want to double check to be sure I know which one I should use.

The wire that goes to the oxygen sensor, should that be connected between the first and second resistors as viewed from the positive end of the 1.5 volt battery or as viewed from the negative end of the 1.5 volt battery?

Thanks again

[diamondlarry]

It would be the one as viewed from the positive end of the battery. You would want to double-check everything with a multi-meter before making connections to the vehicle.

[caryfd227]

So you want to fool your computer into running lean...

Just be careful and I hope you know what your doing... get too lean and you'll be buying a new engine.

[GasSavers_Erik]

Originally Posted by caryfd227

So you want to fool your computer into running lean...

Just be careful and I hope you know what your doing... get too lean and you'll be buying a new engine.

I really envy the VX lean burn system and thought I could tinker with one of my own

Seriously, I do appreciate the word of caution, yes I'll be listening carefully for spark knock during this limited time test. A few months ago found and patched a leaky vacuum hose (manifold vacuum). It was likely leaking for at least 500 miles.

[ZugyNA]

Originally Posted by Erik

I have been driving around watching a digital multimeter which is tied in to my one wire oxygen sensor wire (87 civic with feedback carb.)

The feedback system seems to be doing its job (readings jump around but 90% of the readings are below .45 volts when cruising on the highway). When I floor it, readings jump up to 0.8 and when decelerating in gear, readings go down to near zero volts.

I want to fool the system into leaning the mix out a little, so if I could just feed 0.5 volts into the oxygen sensor wire, then the computer would think it was running rich and tell the carb to lean it out.

Its the same theory behind the "fever buster" mod that is listed here on the intake temp thread.

So, I figure that all I need is a good low amp DC 0.5 volt source that will mimic a rich mixture oxygen sensor signal, but won't have enough amps to fry the computer.

Any ideas from the electronics whizzes here? How about if I use a 1.5 volt battery and a ton of resistors in series, might that be safe?

I am not looking to do this long term, just for a 30 mile test run.

Thanks in advance for any help.

I've been monitoring an '86 one wire sensor tied to a EFI throttle body system (4x4) and it acts just like yours. I was also using a vac gauge and found that unless I kept the vac above 10-12 " HG...the cycling stopped and it went into open loop. With this truck I had to be very attentive to keep it in closed loop during cruise...headwinds and hills were issues.

I doubt if the .5 V added will do the job because as I understand it...the ECU looks for the cycling AND the avg voltage level to determine the mix. You would need to add extra voltage ON TOP of the cycling voltage...which is what an EFIE does.

O2 sensors are tested for being in spec by watching for the number of cycles in say 10 seconds...if they don't cycle enough they are considered as LAZY and need to be replaced.

You could do damage to both your O2 and your ECU if not careful.

It would be nice to find an easy way to add some voltage TO the O2s cycling voltage...but not so sure it can be done.

[DrivenByNothing]

Running a motor lean can also produce worse emissions. Also, one of the main functions of gasoline is actually to cool the combustion chamber and piston head.

If you use water injection correctly, you should be able to remedy the problems listed above.

Gotta run, I'll post more later.

[JanGeo]

Pot is short for potentiometer which is a variable tapped resistor that can be used as a voltage divider.

You don't want to remove the O2 sensor from the system - what you want to do is add a bias to its output to make the ECU think you are running rich so it will lean out the mixture the amount that you bias it towards rich. That may require a little current from a 1 to 1.5 volt? source through a Pot which will allow you to vary how much rich bias you feed the O2 sensor. THis assumes that a rich sensor reads higher voltage and a lean sensor reads lower voltage. You should use about 50x the resistance of the O2 sensor for the pot or even higher so you only apply a 1/50th or less bias relative to the full output of the O2 sensor. You only want a small variation in the A/F mixture.

[diamondlarry]

I need to clarify my earlier post:

I had a mid 80's K car that had a feedback carb that would run fine without ever being plugged in.

I said that in response to the earlier thread that mentioned the car going into limp-home mode. It will still run ok(won't leave you stranded) but it will, if I remember correctly, default to a rich setting which means removing the O2 sensor completely would be a bad thing.